Mũi taro ren HSS hệ inch UNC YAMAWA

Features
The groove on the cutting edge side of the bite part is cut diagonally so that chips are sent forward, so there is no obstacle due to chips and it is ideal for passing holes.
Use
For drilling through holes.
Work Material: Medium Carbon Steel, Cast Steel, Brass, Aluminum Rolled Material, Aluminum Alloy Casting, Zinc Die Casting.

Made in Japan

Mũi taro ren HSS hệ inch UNF YAMAWA

Features
The groove on the cutting edge side of the bite part is cut diagonally so that chips are sent forward, so there is no obstacle due to chips and it is ideal for passing holes.
Use
For drilling through holes.
Work Material: Medium Carbon Steel, Cast Steel, Cast Iron, Brass, Aluminum Alloy Castings, Zinc Die Casting.

Made in Japan

Mũi taro ren mạ Titan YAMAWA

Features
Ideal for low and medium carbon steels that use water-soluble cutting fluid.
Use
For drilling through holes.
Work Material: Low / Medium / High Carbon Steel, Alloy Steel, Heat-Treated Steel, Aluminum Alloy, Copper Alloy, Cast Steel.

Made in Japan

Mũi taro ren Plus Seri YAMAWA

Features
The point tap has the groove on the cutting edge side of the tap tip biting part cut diagonally in the direction opposite to the winding direction of the screw, and the chips are pushed forward, so there is no obstacle due to chips, and it is suitable for threading through holes. It's perfect.
It can be used for medium-speed machining such as machining centers.
Synchronous feed is recommended.
Use
For drilling through holes.
Work Material: Medium carbon steel.

Made in Japan

Mũi taro HSS hiệu năng cao YAMAWA, TiCN coating

Features
Suitable for machining steel materials (35HRC or less) and light alloys, and also for high-speed machining (20-59m / min).
Use
Work Material: Low Carbon Steel, Medium Carbon Steel, High Carbon Steel, Alloy Steel, Stainless Steel.
For blind hole processing.

Made in Japan

Mũi taro HSS hiệu năng cao YAMAWA, TiCN coating

Features
Suitable for machining steel materials (35HRC or less) and light alloys, and also for high-speed machining (20-50m / min).
Use
Work Material: Low Carbon Steel, Medium Carbon Steel, High Carbon Steel, Alloy Steel, Stainless Steel.
For drilling through holes.

Made in Japan

Mũi taro gia công khô YAMAWA

Features
A roll tap that enables tapping without lubrication on thin steel plates that have been burred and have a relatively short processing length with a size of M6 or less.
Use
For drilling through holes.
Work Material: Low Carbon Steel, Medium Carbon Steel, High Carbon Steel, Alloy Steel, Stainless Steel.

Made in Japan

Mũi taro dùng cho Inox YAMAWA

Features
A roll tap that controls the inner diameter of the female thread.
A roll tap that supports control of the inner diameter of the female thread.
Use
Work Material: Stainless Steel, Low / Medium / High Carbon Steel, Alloy Steel, Tool Steel.
Work Material: Stainless Steel, Carbon Steel, Alloy Steel, Tool Steel

Made in Japan

Mũi taro YAMAWA

Features
A tap for low-speed machining for steel materials that can be used in hand drills and drilling machines.
Use
Work material: Mild steel such as SPC and SS400.

Made in Japan

Mũi taro đa năng YAMAWA

Features
A tap for low-speed machining for steel materials that can be used for hand-cranking and drilling machines.
Use
For drilling through holes.
Work material: Mild steel such as SPC and SS400.

Made in Japan

Mũi taro HSS-CO YAMAWA

Features
The tapping torque is high, and stable screw processing is possible even for tempered materials with a hardness of 35HRC, which was previously considered difficult to process with roll taps.
Use
For blind hole processing.
Work Material: High Carbon Steel, Alloy Steel, Heat-Treated Steel (~ 35HRC).

Made in Japan