Cờ lê cân lực GEDORE

Gedore Torque ATB, with micrometer scale for presetting and mounting of the replaceable insert tools, specially for small wrench sizes from 3.2 mm. Adjustment guard against unintentional adjustment of the torque value, on attaining the torque value the handle bends up to 20°, makes overtorquing impossible. Release accuracy ± 6%, classified according to DIN EN ISO 6789:2003 type 2 class A, with factory test certificate.
 

Đầu vặn mua riêng, không kèm sản phẩm

Có thể dùng kèm đầu vặn:

331392 Ratchet insert GEDORE
331393 Open-end insert GEDORE
331394 Ring insert GEDORE

Made in United kingdom

Cờ lê lực NORBAR

Norbar Industrial, rugged industrial wrench for high torques, with adjustment scale and integrated ratchet function, with push-through square, suitable for clockwise and anti-clockwise tightening. Gentle and accurate triggering owing to response-free bending of the shank as a tangible and visible trigger signal, makes overtightening unlikely. Dust-, splash- and dirt-proof; easily readable dual scale in Nm and Ib/ft. Can be separated into two parts and packaged in this way for easier transportation. Triggering accuracy of ±4% from the set value, according to DIN EN ISO 6789, with declaration of conformity according to DIN EN ISO 6789-1:2017, in hard shell case.

Made in United kingdom

Cờ lê cân lực NORBAR-331140

Norbar Professional, actuation with audible "click" signal, with fine-toothed ratchet for working angle of only 6°, for clockwise and anti-clockwise tightening, large scale length makes it easier to adjust, tightening length independent - it can be used with an extension handle, low weight, accuracy of ±3% from the measured value, in accordance with DIN/ISO 6789, with calibration certificate according to DIN EN ISO 6789-2:2017 and extension handle 500 mm.

Made in United kingdom

Cờ lê cân lực FACOM R.208-25

Facom R.208-25, automatic trigger with acoustic signal, fine scale for presetting, ergonomic plastic handle, tried and tested mechanism with long service life, with reversible ratchet for clockwise tightening, accuracy ±4% from the measured value, with factory test certificate.

Made in Italy

Cờ lê cân lực FACOM 209 PB

Facom 209 PB, automatic trigger with acoustic signal, dual scale (with Nm and ft.lbs) and twin-start thread saves time due to 2x faster adjustment, ergonomic plastic handle, tried and tested mechanism with long service life, with fixed reversible ratchet for clockwise tightening, accuracy ±4% from the measured value, with factory test certificate according to ISO 6789. Supplied in protective plastic tube

Made in Italy

Cờ lê cân lực STAHLWILLE 730NR

Stahlwille 730 NR, with reversible insert ratchet, for clockwise and anticlockwise tightening. Can easily be heard and felt when it triggers; accuracy ±3% according to DIN/ISO 6789, with factory test certificate. Rugged construction, quick setting of torque with QuickSelect; pulling out and turning the setting button sets the torque and then locks it in. The measuring element is only under load when tightening, no need for manual reset to zero.

Đầu vặn đã gắn kèm sản phẩm

Có thể thay bằng các đầu vặn khác:

331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

Linh kiện gốc:
331600 Ratchet insert STAHLWILLE

Made in Germany

Cờ lê cân lực cách điện 1000V STAHLWILLE MANOSKOP® 730R

The MANOSKOP® 730R VDE torque wrench has been specifically designed for use in the electrical sector and is characterised by its high-quality finish and reliability. The torque wrench complies with stringent VDE guidelines, ensuring reliable protection against electrical hazards. Thanks to the easy-to-read scale window and the precise rotary knob, the MANOSKOP® 730R VDE allows users to set the desired torque simply and accurately. The torque wrench triggers mechanically, meaning a noticeable, audible click indicates that the torque is set. This function not only provides increased safety but also ensures that users always work within the required specifications. Another practical function of the MANOSKOP® 730R VDE is the possibility of self-adjustment without the need to disassemble the wrench and re-test the insulation. This flexibility allows users to adjust the torque as required without additional effort. Moreover, there is the option to replace the ratchet, especially with the 725QR VDE model. This function allows users to easily replace the ratchet without having to re-test the insulation. These features make the MANOSKOP® 730R VDE a versatile, user-friendly tool for demanding work in electrical environments.

Properties:

• VDE-compliant up to 1000 V
• Adjustment without disassembly or re-testing
• Ratchet can be replaced without re-testing
• Quick adjustment via QuickSelect rotary knob

Made in Germany

Cờ lê cân lực đầu tháo rời thay thế STAHLWILLE 730 N

Stahlwille 730 N, for clockwise and anticlockwise tightening. Can easily be heard and felt when it triggers; accuracy ±3% according to DIN/ISO 6789, with factory test certificate. Rugged construction, quick setting of torque with QuickSelect; pulling out and turning the setting button sets the torque and then locks it in. The measuring element is only under load when tightening, no need for manual reset to zero.

Đầu vặn cấp riêng, KHÔNG kèm sản phẩm

Có thể dùng kèm đầu vặn:

331600 Ratchet insert STAHLWILLE
331602 Ratchet insert STAHLWILLE 725QR
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE
331636 Open ended insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE
331656 Ring insert STAHLWILLE 732/100
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE
LT000054329 735/65 - Ratchet insert tool, fine tooth
LT000054333 735/100 - Ratchet insert tool
LT000054346 734/100 - Square drive insert tool
LT000054557 737 - Blank end insert tool
LT000054573 7370/100 - Adaptor

tag: 730n

Made in Germany

Cờ lê cân lực STAHLWILLE 730, 730Quick

Stahlwille 730, for clockwise and counter-clockwise tightening. A stop signal which can be clearly heard and felt is automatically given when the correct torque is reached. Accuracy of ±4% in accordance with DIN/ISO 6789, with factory test certificate. Robust design, rapid adjustment of torque with slider and locking button.
Stahlwille 730 Quick, for clockwise and counter-clockwise tightening. More ergonomic and with increased comfort; improved access and operation of the clamping lever recessed in the handle. Optimised ball handle for fatigue-free work. The new design with opposite, V-shaped mounts and integrated magnifier allows settings to be adjusted quickly and accurately - even from an awkward angle. A stop signal which can be clearly heard and felt is automatically given when the correct torque is reached. Accuracy of ±4% in accordance with DIN/ISO 6789, with factory test certificate. Robust design, rapid adjustment of torque with slider and locking button.

Đầu vặn cấp riêng, KHÔNG kèm sản phẩm

Có thể dùng kèm đầu vặn:

331600 Ratchet insert STAHLWILLE
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE

331635 Open-end insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE

331655 Ring-end insert STAHLWILLE
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

331684 Adapter insert STAHLWILLE

Made in Germany

Cờ lê cân lực STAHLWILLE 730 FIX

Stahlwille 730 Fix, for series production tasks; the adjusting knob can be removed after the torque has been set, preventing inadvertent changes to the settings. The Torx® tamper-resistant screw also protects against unwanted manipulation, just like the enclosed adhesive seal; settings cannot be adjusted without breaking the seal. For clockwise and counter-clockwise tightening by turning over the insert tools. Robust design, rapid adjustment of torque with QuickSelect; the torque is set and then locked by pulling out the adjusting knob and turning it. Two-component handle with ergonomic green soft zone (resistant to oils, greases, fuels, brake fluids and Skydrol). A stop signal which can be clearly heard and felt is automatically given when the correct torque is reached; accuracy ±3% in accordance with DIN 6789. No need for manual reset to zero, since the measuring element is only under load while force is being applied. Supplied with factory certificate, Torx® tamper-resistant screw and adhesive seal. Without insert tool.

Đầu vặn cấp riêng, KHÔNG kèm sản phẩm

Có thể dùng kèm đầu vặn:

331600 Ratchet insert STAHLWILLE
331602 Ratchet insert STAHLWILLE 725QR
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE
331636 Open ended insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE
331656 Ring insert STAHLWILLE 732/100
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

LT000054329 735/65 - Ratchet insert tool, fine tooth
LT000054333 735/100 - Ratchet insert tool
LT000054346 734/100 - Square drive insert tool
LT000054557 737 - Blank end insert tool
LT000054573 7370/100 - Adaptor

Made in Germany

Cờ lê cân lực FUTURO-331205

For controlled clockwise tightening, with ratchet wrench, automatic actuation with audible signal. Double micrometer scale Nm and lbf/in / lbf/ft allows for exact, error-free setting. Quick adjustment, ergonomic 2-component handle, accuracy of ±3% from measured value (more accurate than DIN EN ISO 6789), with declaration of conformity to DIN EN ISO 6789-1:2017.

Made in United kingdom

KS Tools Double ended sword and rounded head lever, 200mm 911.8109

For controlled clockwise and anti-clockwise tightening, robust ratchet with push-through square, automatic actuation with audible signal. Double micrometer scale Nm and lbf/ft allows for exact, error-free setting. Quick adjustment, ergonomic 2-component handle, accuracy of ±3% from measured value (more accurate than DIN EN ISO 6789), with declaration of conformity to DIN EN ISO 6789-1:2017.

Made in United kingdom

Cờ lê cân lực HAZET 5108-3CT

HAZET 5108-3CT, accuracy ± 3% from scale value, designed for harsh workshop use, for controlled fastening with haptic and acoustic feedback. Adjustment aid in the form of detent points means that the required torque value can be set quickly and securely by simply turning the handle. Triangle-shaped slewing ring stops the tool from rolling away unintentionally. Easy-to-read, high-contrast scale (laser inscribed), integrated switchover lever, tested in accordance with DIN EN ISO 6789-2:2017 with factory test certificate.

Made in Germany

Cờ lê cân lực HAZET 5111-3CT

HAZET 5111-3CT, accuracy ± 3% from scale value, designed for harsh workshop use, for controlled fastening with haptic and acoustic feedback. Adjustment aid in the form of detent points means that the required torque value can be set quickly and securely by simply turning the handle. Triangle-shaped slewing ring stops the tool from rolling away unintentionally. Easy-to-read, high-contrast scale (laser inscribed), integrated switchover lever, tested in accordance with DIN EN ISO 6789-2:2017 with factory test certificate.

tag: 51113ct

Made in Germany

Cờ lê cân lực HAZET 5143-3CT

HAZET 5143-3CT, accuracy ± 3% from scale value, designed for harsh workshop use, for controlled fastening with haptic and acoustic feedback. Adjustment aid in the form of detent points means that the required torque value can be set quickly and securely by simply turning the handle. Triangle-shaped slewing ring stops the tool from rolling away unintentionally. Easy-to-read, high-contrast scale (laser inscribed), integrated switchover lever, tested in accordance with DIN EN ISO 6789-2:2017 with factory test certificate.

tag: 51433ct

Made in Germany

Cờ lê cân lực NERIOX

Automatically triggering torque wrench for controlled right-hand tightening, error-free and accurate torque pre-setting via easy-to-read laser scale, with audible and tactile signal when the pre-set torque is reached. Reversible ratchet and robust metal handle. High accuracy of the measured value according to DIN/ISO 6789-1:2017, with factory test certificate and plastic case.

Made in Germany

Cờ lê cân lực HAZET

Hazet 6000-1 CT, for controlled clockwise fastening, with automatic close-gap release, palpably and audibly discernible when the value set is reached, easy and safe adjustment of the torque value desired by turning the handle.

Designs:
1...6 Nm: Accuracy ± 4 % of the scale value
2...10 Nm...4...40 Nm: Accuracy ± 2% of the scale value

Made in Germany

Cờ lê cân lực HAZET

Hazet 6000-1 CT, ± 2% release accuracy of the scale value, highly precise premium measuring instruments for the heaviest demands. Robust and wear-resistant hard-chrome-plated steel tube construction in slimline design, in safe box with display. Safety locking of the handle, adjusting knob for collateral locking of the calibration, user-friendly reversible ratchet, service-friendly, integrated shift lever, adjustment of the torque value desired easily and safely by turning the handle, ergonomically shaped handle with collar reduces the risk of slipping or injury, precise, fine scale graduation.

Made in Germany

Cờ lê cân lực HAZET

Hazet 6000-1 CT, for the highest torque values, application on wind turbines, in dockyards, in the aviation and heavy industry, in the commercial vehicle industry, etc. To be disassembled two parts with release tool in carrier bag with carrying handle and shoulder strap, fast screw tightening also possible with ratchet shaft, for torque controlled tightening always use the complete wrench.

Designs:
400...1000 Nm...600...1600 Nm: Accuracy ± 3 % of the scale value
800...2000 Nm: Accuracy ± 4 % of the scale value

Made in Germany