Mũi taro Carbide gia công gang YAMAWA

Features
A carbide tap suitable for threading mass-produced hard and brittle materials such as cast iron.
Use
Work Material: Cast Iron, Tough Cast Iron, Brass Casting.

Made in Japan

Mũi taro Carbide YAMAWA

Features
Carbide tap suitable for thread processing of mass-produced products such as aluminum casting (AC), aluminum die casting (ADC), and zinc die casting (ZDC).
Use
Work material: Aluminum alloy casting, zinc alloy casting.

Made in Japan

Mũi taro lỗ cho kim loại phi từ tính YAMAWA

Features
A roll tap suitable for threading non-ferrous metals (aluminum castings, aluminum die castings, brass, etc.).
Use
For blind hole processing.
Work Material: For rolled aluminum materials, aluminum alloy castings, and zinc alloy castings.

Made in Japan

Mũi taro xuyên lỗ cho kim loại phi từ tính YAMAWA

Features
A roll tap suitable for threading non-ferrous metals (aluminum castings, aluminum die castings, brass, etc.).
Use
For drilling through holes.
Work Material: For rolled aluminum materials, aluminum alloy castings, and zinc alloy castings.

Made in Japan

Mũi taro mạ Titan gia công xuyên lỗ YAMAWA

Features
A coated roll tap suitable for threading steel-based and non-ferrous metals.
Use
Work material: Low carbon steel, medium carbon steel.
Through hole thread: Metric thread
For drilling through holes

Made in Japan

Mũi taro Carbide cho thép siêu cứng YAMAWA

Features
Ideal for tapping 55-60 (Max65) HRC of SKD material and pre-hardened steel.
Uses ultrafine cemented carbide with excellent wear resistance and impact resistance.
The runout accuracy of the entire tap and the roundness of the shank are improved.
The thread processing length is "outer diameter dimension X1.5 or less", and the bite is 5P in consideration of the life.
For the prepared hole diameter, we recommend the maximum inner diameter of 6H female thread.
Use
Work material: Heat-treated steel.

Made in Japan

Mũi taro ren HSS hệ inch YAMAWA

Features
It is a tap for unified screws and is used in all directions.
Use
For drilling through holes.
Work material: Medium carbon steel.

Made in Japan

Mũi taro ren HSS hệ inch YAMAWA

Features
The groove on the cutting edge side of the bite part is cut diagonally so that chips are sent forward, so there is no obstacle due to chips and it is ideal for passing holes.
Since the straight groove is shallow, the strength is high.
Use
For drilling through holes.
Work Material: Medium carbon steel, copper alloy, aluminum alloy.

Made in Japan

Mũi taro ren HSS YAMAWA

Features
The groove on the cutting edge side of the bite part is cut diagonally so that chips are sent forward, so there is no obstacle due to chips and it is ideal for passing holes.
Since the straight groove is shallow, the strength is high.
Use
For drilling through holes.
Work Material: Medium Carbon Steel, Cast Steel, Brass, Rolled Aluminum, Aluminum Alloy Casting, Die Casting.

Made in Japan

Mũi taro gia công gang YAMAWA

Features
Since it is suitable for hard and brittle materials such as cast iron, it wears relatively quickly, so it is an oversized tap that allows for the amount of wear.
Use
Work material: Cast iron.

Made in Japan

Mũi taro lỗ cho thép YAMAWA

Features
A roll tap suitable for threading steel (carbon steel, alloy steel, ordinary steel).
Use
For blind hole processing.
Work material: For low carbon steel and medium carbon steel.

Made in Japan

Mũi taro xuyên lỗ cho thép YAMAWA

Features
A roll tap suitable for threading steel (carbon steel, alloy steel, ordinary steel).
Use
For drilling through holes.
Work material: For low carbon steel and medium carbon steel.

Made in Japan