Cờ lê lực NORBAR

Norbar Industrial, rugged industrial wrench for high torques, with adjustment scale and integrated ratchet function, with push-through square, suitable for clockwise and anti-clockwise tightening. Gentle and accurate triggering owing to response-free bending of the shank as a tangible and visible trigger signal, makes overtightening unlikely. Dust-, splash- and dirt-proof; easily readable dual scale in Nm and Ib/ft. Can be separated into two parts and packaged in this way for easier transportation. Triggering accuracy of ±4% from the set value, according to DIN EN ISO 6789, with declaration of conformity according to DIN EN ISO 6789-1:2017, in hard shell case.

Made in United kingdom

Cờ lê cân lực NORBAR-331140

Norbar Professional, actuation with audible "click" signal, with fine-toothed ratchet for working angle of only 6°, for clockwise and anti-clockwise tightening, large scale length makes it easier to adjust, tightening length independent - it can be used with an extension handle, low weight, accuracy of ±3% from the measured value, in accordance with DIN/ISO 6789, with calibration certificate according to DIN EN ISO 6789-2:2017 and extension handle 500 mm.

Made in United kingdom

Cờ lê cân lực STAHLWILLE 730NR

Stahlwille 730 NR, with reversible insert ratchet, for clockwise and anticlockwise tightening. Can easily be heard and felt when it triggers; accuracy ±3% according to DIN/ISO 6789, with factory test certificate. Rugged construction, quick setting of torque with QuickSelect; pulling out and turning the setting button sets the torque and then locks it in. The measuring element is only under load when tightening, no need for manual reset to zero.

Đầu vặn đã gắn kèm sản phẩm

Có thể thay bằng các đầu vặn khác:

331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

Linh kiện gốc:
331600 Ratchet insert STAHLWILLE

Made in Germany

Cờ lê cân lực đầu tháo rời thay thế STAHLWILLE 730 N

Stahlwille 730 N, for clockwise and anticlockwise tightening. Can easily be heard and felt when it triggers; accuracy ±3% according to DIN/ISO 6789, with factory test certificate. Rugged construction, quick setting of torque with QuickSelect; pulling out and turning the setting button sets the torque and then locks it in. The measuring element is only under load when tightening, no need for manual reset to zero.

Đầu vặn cấp riêng, KHÔNG kèm sản phẩm

Có thể dùng kèm đầu vặn:

331600 Ratchet insert STAHLWILLE
331602 Ratchet insert STAHLWILLE 725QR
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE
331636 Open ended insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE
331656 Ring insert STAHLWILLE 732/100
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE
LT000054329 735/65 - Ratchet insert tool, fine tooth
LT000054333 735/100 - Ratchet insert tool
LT000054346 734/100 - Square drive insert tool
LT000054557 737 - Blank end insert tool
LT000054573 7370/100 - Adaptor

tag: 730n

Made in Germany

Cờ lê cân lực STAHLWILLE 730R

Stahlwille 730 R, with reversible adapter ratchet, for clockwise and anticlockwise tightening. Can easily be heard and felt when it triggers, accuracy ±4% according to DIN/ISO 6789, with factory test certificate, rugged construction, quick setting of torque with slide and locking button.

Đầu vặn Đàbao gồm

Có thể dùng đầu vặn khác thay thế:

331600 Ratchet insert STAHLWILLE
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE

331635 Open-end insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE

331655 Ring-end insert STAHLWILLE
331656 Ring insert STAHLWILLE 732/100
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

331684 Adapter insert STAHLWILLE

Link kiện gốc:

331600 Ratchet insert STAHLWILLE

Made in Germany

Cờ lê cân lực STAHLWILLE 730, 730Quick

Stahlwille 730, for clockwise and counter-clockwise tightening. A stop signal which can be clearly heard and felt is automatically given when the correct torque is reached. Accuracy of ±4% in accordance with DIN/ISO 6789, with factory test certificate. Robust design, rapid adjustment of torque with slider and locking button.
Stahlwille 730 Quick, for clockwise and counter-clockwise tightening. More ergonomic and with increased comfort; improved access and operation of the clamping lever recessed in the handle. Optimised ball handle for fatigue-free work. The new design with opposite, V-shaped mounts and integrated magnifier allows settings to be adjusted quickly and accurately - even from an awkward angle. A stop signal which can be clearly heard and felt is automatically given when the correct torque is reached. Accuracy of ±4% in accordance with DIN/ISO 6789, with factory test certificate. Robust design, rapid adjustment of torque with slider and locking button.

Đầu vặn cấp riêng, KHÔNG kèm sản phẩm

Có thể dùng kèm đầu vặn:

331600 Ratchet insert STAHLWILLE
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE

331635 Open-end insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE

331655 Ring-end insert STAHLWILLE
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

331684 Adapter insert STAHLWILLE

Made in Germany

Cờ lê cân lực STAHLWILLE 730 FIX

Stahlwille 730 Fix, for series production tasks; the adjusting knob can be removed after the torque has been set, preventing inadvertent changes to the settings. The Torx® tamper-resistant screw also protects against unwanted manipulation, just like the enclosed adhesive seal; settings cannot be adjusted without breaking the seal. For clockwise and counter-clockwise tightening by turning over the insert tools. Robust design, rapid adjustment of torque with QuickSelect; the torque is set and then locked by pulling out the adjusting knob and turning it. Two-component handle with ergonomic green soft zone (resistant to oils, greases, fuels, brake fluids and Skydrol). A stop signal which can be clearly heard and felt is automatically given when the correct torque is reached; accuracy ±3% in accordance with DIN 6789. No need for manual reset to zero, since the measuring element is only under load while force is being applied. Supplied with factory certificate, Torx® tamper-resistant screw and adhesive seal. Without insert tool.

Đầu vặn cấp riêng, KHÔNG kèm sản phẩm

Có thể dùng kèm đầu vặn:

331600 Ratchet insert STAHLWILLE
331602 Ratchet insert STAHLWILLE 725QR
331610 Bit ratchet insert STAHLWILLE
331613 Bit holder insert STAHLWILLE
331620 Open-end insert STAHLWILLE
331630 Open-end insert STAHLWILLE
331636 Open ended insert STAHLWILLE
331637 Open ring insert STAHLWILLE
331640 Ring-end insert STAHLWILLE
331650 Ring-end insert STAHLWILLE
331656 Ring insert STAHLWILLE 732/100
331660 Square insert STAHLWILLE
331680 Weld-on insert STAHLWILLE
331682 Adapter insert STAHLWILLE
331683 Adapter insert STAHLWILLE

LT000054329 735/65 - Ratchet insert tool, fine tooth
LT000054333 735/100 - Ratchet insert tool
LT000054346 734/100 - Square drive insert tool
LT000054557 737 - Blank end insert tool
LT000054573 7370/100 - Adaptor

Made in Germany

Cờ lê cân lực FUTURO

For controlled clockwise and anti-clockwise tightening, robust ratchet with push-through square, automatic actuation with audible signal. Double micrometer scale Nm and lbf/ft allows for exact, error-free setting. Quick adjustment, ergonomic 2-component handle, accuracy of ±3% from measured value (more accurate than DIN EN ISO 6789), with declaration of conformity to DIN EN ISO 6789-1:2017.

Made in United kingdom

Cờ lê cân lực HAZET

Hazet 6000-1 CT, for the highest torque values, application on wind turbines, in dockyards, in the aviation and heavy industry, in the commercial vehicle industry, etc. To be disassembled two parts with release tool in carrier bag with carrying handle and shoulder strap, fast screw tightening also possible with ratchet shaft, for torque controlled tightening always use the complete wrench.

Designs:
400...1000 Nm...600...1600 Nm: Accuracy ± 3 % of the scale value
800...2000 Nm: Accuracy ± 4 % of the scale value

Made in Germany

Cờ lê cân lực GEDORE

Gedore DREMOMETER 8581, lightweight, rugged and resistant, ideal for use in workshops and almost all industrial manufacturing plants. Automatic rapid release with tactile and audible signal, values are not shifted and accuracy is not impacted as a result of using both hands or the actuation button being situated in a location other than the handle (as is the case with conventional torque wrenches). Both the square drive and centre of rotation are on one axis, resulting in high operating safety; can be extended to reduce the user's workload. Classified in accordance with DIN EN ISO 6789-2:2017 Type II Class A, including traceable test certificate, calibrated to a maximum permitted deviation of ± 3% and therefore more precise than the value of ± 4% required by the standard.

TAG: 858101

Made in Germany

Cờ lê cân lực GEDORE

Gedore DREMOMETER 8586, lightweight, rugged and resistant with double-square drive, ideal for use in workshops and almost all industrial manufacturing plants. Automatic rapid release with tactile and audible signal, values are not shifted and accuracy is not impacted as a result of using both hands or the actuation button being situated in a location other than the handle (as is the case with conventional torque wrenches). Both the square drive and centre of rotation are on one axis, resulting in high operating safety; can be extended to reduce the user's workload. Classified in accordance with DIN EN ISO 6789-2:2017 Type II Class A, including traceable test certificate, calibrated to a maximum permitted deviation of ± 3% and therefore more precise than the value of ± 4% required by the standard.

TAG: 858601
 

Made in Germany